0 NO SENSE
00 00 No additional sense data available.
00 01 Filemark detected.
00 02 End of tape or partition detected.
00 03 Setmark detected.
00 04 Beginning of partition or media.
1 RECOVERED ERROR
18 01 Recovered data with error condition and retries applied.
37 00 Rounded parameter.
5B 00 Log exception.
5B 02 Log counter at maximum
2 NOT READY
04 01 Logical unit is in process of becoming ready.
04 03 Logical unit not ready, manual intervention required
30 00 Incompatible medium installed.
30 03 Cleaning cartridge installed.
30 04 Diagnostic cartridge installed.
3A 00 Cartridge or magazine not present.
53 00 Cartridge load/eject failure.
5A 91 Eject button pushed.
3 MEDIUM ERROR
00 02 End of tape or partition detected
03 02 Excessive write errors.
0C 00 Write error during compression.
11 00 Unrecovered read error.
30 00 Bad entity header.
30 01 Cannot read tape, unknown format.
30 02 Cannot read tape, incompatible format.
30 11 Entity header wrong length.
30 12 Reserve byte not in entity header.
30 13 Bad algorithm byte in entity header.
30 C3 Compressed data format corruption.
30 C4 Block Access Table corruption during reading.
30 C5 Block Access Table corruption during space.
31 00 Tape format corrupted.
3B 00 Sequential positioning error.
3B 01 Tape position error at BOT.
3B 08 Lost tape position.
44 B3 Gain adjustment failure.
70 xx Decompression exception where xx specifies the illegal algorithm
4 HARDWARE ERROR
00 00 SPACE command logic error.
15 01 Mechanical positioning error.
20 00 Receive data DMA length error.
21 00 Send data DMA length error.
40 80 Diagnostic failed unknown test.
40 81 Diagnostic failed PROM Checksum test.
40 82 Diagnostic failed RAM test.
40 83 Diagnostic failed Memory Controller test.
40 84 Diagnostic failed Counter/Timer test.
40 85 Diagnostic failed SCSI LSI test.
40 86 Diagnostic failed ECC processor test.
40 87 Diagnostic failed Drive LSI test.
40 88 Diagnostic failed Compression LSI test.
40 89 Diagnostic failed EEPROM test
40 90 Tape read/write test failed.
44 00 Internal failure.
44 01 Internal failure: invalid completion code.
44 02 Internal failure: ISR failure.
44 80 Compression hardware fault.
44 81 Port A parity error.
44 82 Port B parity error.
44 90 Error during compression.
44 91 Port B control problem.
44 92 Compression LSI pause problem.
44 93 Error during buffer swap.
44 94 Compression chip not paused when expected.
44 95 FIFO not empty when expected.
44 96 Compression chip not flushed when expected.
44 9A Timeout during background operation.
44 AD Capstan servo error.
44 AE Tape cylinder error.
44 AF Tape reel error.
44 B0 Unknown mechanical error.
44 B1 The tape is cut.
44 B2 The tape is jammed.
44 B4 Tape process internal error.
44 B7 Internal error: invalid tape status.
44 B8 Internal error: invalid control mode.
44 B9 Internal error: drive error.
44 BA Internal error: SDA search failed.
44 BB Internal error: tape erase failed.
44 BC Internal error: invalid Append AFC.
44 BD Internal error: missed SP3 interrupt.
44 C0 Magazine scanning to 1st detectable slot failed during initialization (Autoloader only).
44 C1 Magazine positioning from one slot to next failed during initializationAutoloader only).
44 C2 Magazine ejection failure (Autoloader only).
44 C3 Upward magazine movement failure (Autoloader only).
44 C4 Downward magazine movement failure (Autoloader only).
44 C5 Cartridge could not successfully be inserted (Autoloader only).
44 C6 Cartridge insertion rollers could not engage (Autoloader only).
44 C7 Cartridge insertion rollers could not disengage (Autoloader only).
44 C8 Cartridge ejection failure (Autoloader only).
44 C9 Cartridge rollers could not engage during ejection (Autoloader only).
44 CA Cartridge rollers could not disengage during ejection(Autoloader only).
44 CB Drawer closing failure (Autoloader only).
44 CC Drawer opening failure (Autoloader only).
44 CD Magazine could not initialize to a known state after power-up(Autoloader only).
45 00 Select or reselect failure.
46 00 Unsuccessful soft reset.
4B 00 Data Phase error.
51 00 Erase failure.
52 00 Cartridge fault.
53 00 Tape load failure
53 01 Unload tape failure.
82 80 Dew sensor
5 ILLEGAL REQUEST
1A 00 Invalid parameter list length.
20 00 Invalid CDB operation code.
21 01 Invalid element address.
24 00 Invalid field in CDB.
25 00 Logical unit not supported.
26 00 Invalid field in the parameter list.
26 01 Parameter not supported.
26 02 Parameter value invalid.
26 03 Threshold parameters not supported.
39 00 Saved bit not supported.
3A 00 Cartridge or magazine not present
3B 0D Destination element full.
3B 0E Source element empty.
3D 00 Invalid bits in Identify message.
6 UNIT ATTENTION
28 00 Not ready to ready transition (cartridge or magazine change).
29 00 Power on or reset.
2A 01 Mode parameters changed.
5A 01 Cartridge was changed.
5B 01 Threshold condition met.
7 DATA PROTECT
27 00 Write protected.
30 00 Nn-MRS media
8 BLANK CHECK
00 05 End of data (EOD) detected.
30 01 Cannot read tape, unrecorded or unknown format.
B ABORTED COMMAND
1B 00 Host did not respond to SDTN message.
43 00 Message error.
45 00 Select or reselect failure.
47 00 SCSI parity error detected.
48 00 Initiator-detected error message received.
49 00 Invalid message error.
4A 00 Command Phase error.
4E 00 Reconnect abort error
53 00 Cartridge load/eject failure.
5A 01 Cartridge ejected.
D VOLUME OVERFLOW
00 02 End of partition/tape detected.